| Author |
Message |
Darren
Guest
|
 Posted:
Sun Feb 06, 2005 8:35 am Post subject:
AT PSU changeover to ATX PSU. Power button-buy one? |
|
|
Hi
My spare PC is in an AT case. It's currently powered by a 200w AT power
supply.
The motherboard has AT and ATX connectors. The mobo is an Epox EP-58
MVP3C-M and has power connectors for both AT and ATX cases.
I'm taking out the generic AT 200w power supply as it's getting old and I
have a new 400w ATX power supply to put in.
The AT PSU has a power cord which runs to a button on the front of the case.
The ATX PSU does not have a power cord with a button attached to it.
I've noticed the mobo has a 2 pin connector labelled 'POWER-ON'.
After installing the new ATX PSU, is it a case of buying a power button with
two wires that go to the 2 pin 'POWER-ON' connector?
If so, I'm not sure which pin will be positive and which will be negative
and I'm not sure my mobo manual tells me...
I suppose that electronics shops would stock these buttons.
I'm from downunder, if that helps with PC component location advice.
Thanks heaps
Darren
|
|
| Back to top |
|
 |
James Sweet
Guest
|
| Posted:
Sun Feb 06, 2005 8:40 am Post subject:
Re: AT PSU changeover to ATX PSU. Power button-buy one? |
|
|
"Bob Urz" <sound@inetnebr.com> wrote in message
news:42058fc4$1_1@127.0.0.1...
| Quote: |
Darren wrote:
Hi
My spare PC is in an AT case. It's currently powered by a 200w AT power
supply.
The motherboard has AT and ATX connectors. The mobo is an Epox EP-58
MVP3C-M and has power connectors for both AT and ATX cases.
I'm taking out the generic AT 200w power supply as it's getting old and
I
have a new 400w ATX power supply to put in.
The AT PSU has a power cord which runs to a button on the front of the
case.
The ATX PSU does not have a power cord with a button attached to it.
I've noticed the mobo has a 2 pin connector labelled 'POWER-ON'.
After installing the new ATX PSU, is it a case of buying a power button
with
two wires that go to the 2 pin 'POWER-ON' connector?
If so, I'm not sure which pin will be positive and which will be
negative
and I'm not sure my mobo manual tells me...
I suppose that electronics shops would stock these buttons.
I'm from downunder, if that helps with PC component location advice.
Thanks heaps
Darren
perhaps you can recycle the unused "Turbo" button......
|
That would work except that usually that's a latching button, though the
latch mechanism may be removable. Could use the reset button as well but
then of course you lose the reset function. |
|
| Back to top |
|
|
Darren
Guest
|
| Posted:
Sun Feb 06, 2005 8:40 am Post subject:
Re: AT PSU changeover to ATX PSU. Power button-buy one? |
|
|
Good idea bob. I'll look at that.
As far as replacing, fair comment Sam but the old one has no essential
functions for failure, overload etc and the new one has and was free.
Thanks
Darren
"Bob Urz" <sound@inetnebr.com> wrote in message
news:42058fc4$1_1@127.0.0.1...
| Quote: |
Darren wrote:
Hi
My spare PC is in an AT case. It's currently powered by a 200w AT power
supply.
The motherboard has AT and ATX connectors. The mobo is an Epox EP-58
MVP3C-M and has power connectors for both AT and ATX cases.
I'm taking out the generic AT 200w power supply as it's getting old and
I
have a new 400w ATX power supply to put in.
The AT PSU has a power cord which runs to a button on the front of the
case.
The ATX PSU does not have a power cord with a button attached to it.
I've noticed the mobo has a 2 pin connector labelled 'POWER-ON'.
After installing the new ATX PSU, is it a case of buying a power button
with
two wires that go to the 2 pin 'POWER-ON' connector?
If so, I'm not sure which pin will be positive and which will be
negative
and I'm not sure my mobo manual tells me...
I suppose that electronics shops would stock these buttons.
I'm from downunder, if that helps with PC component location advice.
Thanks heaps
Darren
perhaps you can recycle the unused "Turbo" button......
Bob
----== Posted via Newsfeeds.Com - Unlimited-Uncensored-Secure Usenet
News==----
http://www.newsfeeds.com The #1 Newsgroup Service in the World! 120,000+
Newsgroups
----= East and West-Coast Server Farms - Total Privacy via Encryption
=---- |
|
|
| Back to top |
|
|
Darren
Guest
|
| Posted:
Sun Feb 06, 2005 8:40 am Post subject:
Re: AT PSU changeover to ATX PSU. Power button-buy one? |
|
|
I was hoping polarity wasn't an issue. Thanks very much.
"James Sweet" <jamessweet@hotmail.com> wrote in message
news:VEgNd.12928$wc.4615@trnddc07...
| Quote: |
"Sam Goldwasser" <sam@saul.cis.upenn.edu> wrote in message
news:6wk6pmfkf1.fsf@saul.cis.upenn.edu...
As they say: "If it ain't broke, why fix it"?
What's wrong with an old supply if it does the job? Unless there are
problems, or you are seriously expanding it, a new power supply won't
make it run better. :)
Either way to answer the question, polarity doesn't matter for the
pushbutton, any momentary button will work, all it does is connect the two
wires together when you press it.
|
|
|
| Back to top |
|
|
Sam Goldwasser
Guest
|
| Posted:
Sun Feb 06, 2005 8:40 am Post subject:
Re: AT PSU changeover to ATX PSU. Power button-buy one? |
|
|
As they say: "If it ain't broke, why fix it"?
What's wrong with an old supply if it does the job? Unless there are
problems, or you are seriously expanding it, a new power supply won't
make it run better. :)
--- sam | Sci.Electronics.Repair FAQ Mirror: http://repairfaq.ece.drexel.edu/
Repair | Main Table of Contents: http://repairfaq.ece.drexel.edu/REPAIR/
+Lasers | Sam's Laser FAQ: http://repairfaq.ece.drexel.edu/sam/lasersam.htm
| Mirror Sites: http://repairfaq.ece.drexel.edu/REPAIR/F_mirror.html
Note: These links are hopefully temporary until we can sort out the excessive
traffic on Repairfaq.org.
Important: Anything sent to the email address in the message header above is
ignored unless my full name is included in the subject line. Or, you can
contact me via the Feedback Form in the FAQs.
"Darren" <no@replypls.com> writes:
| Quote: | Hi
My spare PC is in an AT case. It's currently powered by a 200w AT power
supply.
The motherboard has AT and ATX connectors. The mobo is an Epox EP-58
MVP3C-M and has power connectors for both AT and ATX cases.
I'm taking out the generic AT 200w power supply as it's getting old and I
have a new 400w ATX power supply to put in.
The AT PSU has a power cord which runs to a button on the front of the case.
The ATX PSU does not have a power cord with a button attached to it.
I've noticed the mobo has a 2 pin connector labelled 'POWER-ON'.
After installing the new ATX PSU, is it a case of buying a power button with
two wires that go to the 2 pin 'POWER-ON' connector?
If so, I'm not sure which pin will be positive and which will be negative
and I'm not sure my mobo manual tells me...
I suppose that electronics shops would stock these buttons.
I'm from downunder, if that helps with PC component location advice.
Thanks heaps
Darren |
|
|
| Back to top |
|
|
Bob Urz
Guest
|
| Posted:
Sun Feb 06, 2005 8:40 am Post subject:
Re: AT PSU changeover to ATX PSU. Power button-buy one? |
|
|
Darren wrote:
| Quote: | Hi
My spare PC is in an AT case. It's currently powered by a 200w AT power
supply.
The motherboard has AT and ATX connectors. The mobo is an Epox EP-58
MVP3C-M and has power connectors for both AT and ATX cases.
I'm taking out the generic AT 200w power supply as it's getting old and I
have a new 400w ATX power supply to put in.
The AT PSU has a power cord which runs to a button on the front of the case.
The ATX PSU does not have a power cord with a button attached to it.
I've noticed the mobo has a 2 pin connector labelled 'POWER-ON'.
After installing the new ATX PSU, is it a case of buying a power button with
two wires that go to the 2 pin 'POWER-ON' connector?
If so, I'm not sure which pin will be positive and which will be negative
and I'm not sure my mobo manual tells me...
I suppose that electronics shops would stock these buttons.
I'm from downunder, if that helps with PC component location advice.
Thanks heaps
Darren
perhaps you can recycle the unused "Turbo" button...... |
Bob
----== Posted via Newsfeeds.Com - Unlimited-Uncensored-Secure Usenet News==----
http://www.newsfeeds.com The #1 Newsgroup Service in the World! 120,000+ Newsgroups
----= East and West-Coast Server Farms - Total Privacy via Encryption =---- |
|
| Back to top |
|
|
James Sweet
Guest
|
| Posted:
Sun Feb 06, 2005 8:40 am Post subject:
Re: AT PSU changeover to ATX PSU. Power button-buy one? |
|
|
"Sam Goldwasser" <sam@saul.cis.upenn.edu> wrote in message
news:6wk6pmfkf1.fsf@saul.cis.upenn.edu...
| Quote: | As they say: "If it ain't broke, why fix it"?
What's wrong with an old supply if it does the job? Unless there are
problems, or you are seriously expanding it, a new power supply won't
make it run better. :)
|
Either way to answer the question, polarity doesn't matter for the
pushbutton, any momentary button will work, all it does is connect the two
wires together when you press it. |
|
| Back to top |
|
|
Ken
Guest
|
| Posted:
Sun Feb 06, 2005 8:25 pm Post subject:
Re: AT PSU changeover to ATX PSU. Power button-buy one? |
|
|
Darren wrote:
| Quote: | Good idea bob. I'll look at that.
As far as replacing, fair comment Sam but the old one has no essential
functions for failure, overload etc and the new one has and was free.
Thanks
Darren
"Bob Urz" <sound@inetnebr.com> wrote in message
news:42058fc4$1_1@127.0.0.1...
Darren wrote:
Hi
My spare PC is in an AT case. It's currently powered by a 200w AT power
supply.
The motherboard has AT and ATX connectors. The mobo is an Epox EP-58
MVP3C-M and has power connectors for both AT and ATX cases.
I'm taking out the generic AT 200w power supply as it's getting old and
I
have a new 400w ATX power supply to put in.
The AT PSU has a power cord which runs to a button on the front of the
case.
The ATX PSU does not have a power cord with a button attached to it.
I've noticed the mobo has a 2 pin connector labelled 'POWER-ON'.
After installing the new ATX PSU, is it a case of buying a power button
with
two wires that go to the 2 pin 'POWER-ON' connector?
If so, I'm not sure which pin will be positive and which will be
negative
and I'm not sure my mobo manual tells me...
I suppose that electronics shops would stock these buttons.
I'm from downunder, if that helps with PC component location advice.
Thanks heaps
Darren
perhaps you can recycle the unused "Turbo" button......
Bob
----== Posted via Newsfeeds.Com - Unlimited-Uncensored-Secure Usenet
News==----
http://www.newsfeeds.com The #1 Newsgroup Service in the World! 120,000+
Newsgroups
----= East and West-Coast Server Farms - Total Privacy via Encryption
=----
|
Some MBs that accept either an AT or ATX PS have a jumper or switch
that must be set depending upon which type you use. You should check
your MB literature for such information. |
|
| Back to top |
|
|
jakdedert
Guest
|
| Posted:
Mon Feb 07, 2005 11:18 pm Post subject:
Re: AT PSU changeover to ATX PSU. Power button-buy one? |
|
|
James Sweet wrote:
| Quote: | "Bob Urz" <sound@inetnebr.com> wrote in message
news:42058fc4$1_1@127.0.0.1...
Darren wrote:
Hi
My spare PC is in an AT case. It's currently powered by a 200w AT
power supply.
The motherboard has AT and ATX connectors. The mobo is an Epox
EP-58 MVP3C-M and has power connectors for both AT and ATX
cases.
I'm taking out the generic AT 200w power supply as it's getting old
and I have a new 400w ATX power supply to put in.
The AT PSU has a power cord which runs to a button on the front of
the case.
The ATX PSU does not have a power cord with a button attached to it.
I've noticed the mobo has a 2 pin connector labelled 'POWER-ON'.
After installing the new ATX PSU, is it a case of buying a power
button with two wires that go to the 2 pin 'POWER-ON' connector?
If so, I'm not sure which pin will be positive and which will be
negative and I'm not sure my mobo manual tells me...
I suppose that electronics shops would stock these buttons.
I'm from downunder, if that helps with PC component location advice.
Thanks heaps
Darren
perhaps you can recycle the unused "Turbo" button......
That would work except that usually that's a latching button, though
the latch mechanism may be removable. Could use the reset button as
well but then of course you lose the reset function.
|
Yeah, but the ATX supply doesn't really seem to mind if you hold the button
down for a bit when cycling it on or off (on all the ones I have, you must
hold the button down for a few seconds to turn off, but mostly 'power off'
is under software control, anyway). I expect the OP could use the original
power switch from the AT supply--or the turbo button--as long as he 'cycled'
it instead of simply turning it on or off.
jak |
|
| Back to top |
|
|
|
|
|
|
FAQ
Memberlist
Register
Profile
Log in to check your private messages
Log in