Slide Mount with Set Screw
Electronics Forum Index Electronics
Circuits, theory, electrons and discussions.
 
 FAQFAQ   MemberlistMemberlist     RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 
 
Google
 
Web ElectronicsHelp.net
Slide Mount with Set Screw

 
Post new topic   Reply to topic    Electronics Forum Index -> Electronics General
Author Message
Jim Thompson
Guest
Posted: Mon Feb 07, 2005 5:30 am    Post subject: Slide Mount with Set Screw Reply with quote
I don't know quite what I'm looking for but I need to do the
following:

Approximately a 3' piece of something easily mountable on the ceiling.

A short (maybe 3-4") sliding movable element mounted on the ceiling
piece with a locking set screw.

When set screw is loose, sliding movable element should slide easily,
but not fall off.

Load (attached to sliding movable element) weighs only a few ounces.

Ideas?

Thanks!

...Jim Thompson
--
| James E.Thompson, P.E. | mens |
| Analog Innovations, Inc. | et |
| Analog/Mixed-Signal ASIC's and Discrete Systems | manus |
| Phoenix, Arizona Voice:(480)460-2350 | |
| E-mail Address at Website Fax:(480)460-2142 | Brass Rat |
| http://www.analog-innovations.com | 1962 |

I love to cook with wine. Sometimes I even put it in the food.

Back to top
SCADA
Guest
Posted: Mon Feb 07, 2005 6:28 am    Post subject: Re: Slide Mount with Set Screw Reply with quote
"Jim Thompson" <thegreatone@example.com> wrote in message
news:qq9d01doac48r1a90tn0tkgkvnakfqi99f@4ax.com...
Quote:
I don't know quite what I'm looking for but I need to do the
following:

Approximately a 3' piece of something easily mountable on the ceiling.

A short (maybe 3-4") sliding movable element mounted on the ceiling
piece with a locking set screw.

When set screw is loose, sliding movable element should slide easily,
but not fall off.

Load (attached to sliding movable element) weighs only a few ounces.

Ideas?

Thanks!

...Jim Thompson
--
| James E.Thompson, P.E. | mens |
| Analog Innovations, Inc. | et |
| Analog/Mixed-Signal ASIC's and Discrete Systems | manus |
| Phoenix, Arizona Voice:(480)460-2350 | |
| E-mail Address at Website Fax:(480)460-2142 | Brass Rat |
| http://www.analog-innovations.com | 1962 |

I love to cook with wine. Sometimes I even put it in the food.

Check with your local electrical supply house, ask for "Kindoff".
Back to top
Jim Thompson
Guest
Posted: Mon Feb 07, 2005 6:57 am    Post subject: Re: Slide Mount with Set Screw Reply with quote
On Sun, 6 Feb 2005 19:28:07 -0500, "SCADA" <SCADA@optonline.net>
wrote:

Quote:

"Jim Thompson" <thegreatone@example.com> wrote in message
news:qq9d01doac48r1a90tn0tkgkvnakfqi99f@4ax.com...
I don't know quite what I'm looking for but I need to do the
following:

Approximately a 3' piece of something easily mountable on the ceiling.

A short (maybe 3-4") sliding movable element mounted on the ceiling
piece with a locking set screw.

When set screw is loose, sliding movable element should slide easily,
but not fall off.

Load (attached to sliding movable element) weighs only a few ounces.

Ideas?

Thanks!

...Jim Thompson

Check with your local electrical supply house, ask for "Kindoff".


Thanks! Good lead...once I deduced it had to be spelled "Kindorf" ;-)

...Jim Thompson
--
| James E.Thompson, P.E. | mens |
| Analog Innovations, Inc. | et |
| Analog/Mixed-Signal ASIC's and Discrete Systems | manus |
| Phoenix, Arizona Voice:(480)460-2350 | |
| E-mail Address at Website Fax:(480)460-2142 | Brass Rat |
| http://www.analog-innovations.com | 1962 |

I love to cook with wine. Sometimes I even put it in the food.

Back to top
SCADA
Guest
Posted: Mon Feb 07, 2005 7:23 am    Post subject: Re: Slide Mount with Set Screw Reply with quote
"Jim Thompson" <thegreatone@example.com> wrote in message
news:v5fd01h4j7u3inatc8ml0gei5srs2dd4ln@4ax.com...
Quote:
On Sun, 6 Feb 2005 19:28:07 -0500, "SCADA" <SCADA@optonline.net
wrote:


"Jim Thompson" <thegreatone@example.com> wrote in message
news:qq9d01doac48r1a90tn0tkgkvnakfqi99f@4ax.com...
I don't know quite what I'm looking for but I need to do the
following:

Approximately a 3' piece of something easily mountable on the ceiling.

A short (maybe 3-4") sliding movable element mounted on the ceiling
piece with a locking set screw.

When set screw is loose, sliding movable element should slide easily,
but not fall off.

Load (attached to sliding movable element) weighs only a few ounces.

Ideas?

Thanks!

...Jim Thompson

Check with your local electrical supply house, ask for "Kindoff".


Thanks! Good lead...once I deduced it had to be spelled "Kindorf" ;-)

...Jim Thompson
--
| James E.Thompson, P.E. | mens |
| Analog Innovations, Inc. | et |
| Analog/Mixed-Signal ASIC's and Discrete Systems | manus |
| Phoenix, Arizona Voice:(480)460-2350 | |
| E-mail Address at Website Fax:(480)460-2142 | Brass Rat |
| http://www.analog-innovations.com | 1962 |

I love to cook with wine. Sometimes I even put it in the food.

Ooops, Typo! Your right, of course!
Back to top
Joerg
Guest
Posted: Tue Feb 08, 2005 4:19 am    Post subject: Re: Slide Mount with Set Screw Reply with quote
Hello Jim,

If it has to slide really easy you could try cabinet drawer rails of the ball bearing type. The shortest ones I have seen were 12" and they are nice and flat (about 1/2" thick). The ones I used had holes that could accommodate a set screw. Now those heavy cabinet drawers can be operated with one finger.

You also might be able to use a short piece of track lighting rails plus one rider.

All at the hardware store.

Regards, Joerg

http://www.analogconsultants.com
Back to top
Guest
Posted: Thu Feb 10, 2005 1:23 am    Post subject: Re: Slide Mount with Set Screw Reply with quote
Does it have to look nice?

If not, find your local Unistrut distributor, get a short length of
channel and a single nut.

Tim.
Back to top
Joerg
Guest
Posted: Thu Feb 10, 2005 6:53 am    Post subject: Re: Slide Mount with Set Screw Reply with quote
Hello Tim,

Quote:
Does it have to look nice?

If not, find your local Unistrut distributor, get a short length of
channel and a single nut.



I'd guess that Mrs.Thompson would voice objection here ;-)

Regards, Joerg

http://www.analogconsultants.com
Back to top
Jim Thompson
Guest
Posted: Thu Feb 10, 2005 7:22 am    Post subject: Re: Slide Mount with Set Screw Reply with quote
On Thu, 10 Feb 2005 00:53:55 GMT, Joerg
<notthisjoergsch@removethispacbell.net> wrote:

Quote:
Hello Tim,

Does it have to look nice?

If not, find your local Unistrut distributor, get a short length of
channel and a single nut.



I'd guess that Mrs.Thompson would voice objection here ;-)

Regards, Joerg

http://www.analogconsultants.com

Naaah! It's in the garage. When new door openers were installed, my
parking guide LEDs need a different mount. "N" is quite anxious to
have them back up and operating... fitting a Q45 in a barely deep
enough garage is challenging without the LED beam ;-)

...Jim Thompson
--
| James E.Thompson, P.E. | mens |
| Analog Innovations, Inc. | et |
| Analog/Mixed-Signal ASIC's and Discrete Systems | manus |
| Phoenix, Arizona Voice:(480)460-2350 | |
| E-mail Address at Website Fax:(480)460-2142 | Brass Rat |
| http://www.analog-innovations.com | 1962 |

I love to cook with wine. Sometimes I even put it in the food.
Back to top
Joerg
Guest
Posted: Thu Feb 10, 2005 7:52 am    Post subject: Re: Slide Mount with Set Screw Reply with quote
Hello Jim,

Do you still have the screw drive from the old opener? There are usually
limit switches at both ends which can be freely moved along the aluminum
track. They also have set screws. You should be able to mount the LED
beam to one of these brackets unless it is really heavy.

We had the same problem, back in Europe. A huge Audi station wagon that
had to be parked just right and two inches from the far end or you
wouldn't even be able to get out. When we moved into this house I
couldn't believe that they called it a two car garage. You could park
two Texas Cadillacs in there and still have 10 feet left.

Regards, Joerg

http://www.analogconsultants.com
Back to top
Jim Thompson
Guest
Posted: Thu Feb 10, 2005 8:19 am    Post subject: Re: Slide Mount with Set Screw Reply with quote
On Thu, 10 Feb 2005 01:52:47 GMT, Joerg
<notthisjoergsch@removethispacbell.net> wrote:

Quote:
Hello Jim,

Do you still have the screw drive from the old opener? There are usually
limit switches at both ends which can be freely moved along the aluminum
track. They also have set screws. You should be able to mount the LED
beam to one of these brackets unless it is really heavy.

We had the same problem, back in Europe. A huge Audi station wagon that
had to be parked just right and two inches from the far end or you
wouldn't even be able to get out. When we moved into this house I
couldn't believe that they called it a two car garage. You could park
two Texas Cadillacs in there and still have 10 feet left.

Regards, Joerg

http://www.analogconsultants.com

Illuminating the dash puts the LED about 2' toward the wall past the
opener location. The mount of the old Genie Screw Drive (Junkus
Maximus :) had angle iron sticking out that far.

I just put in two Chamberlain belt drive units... nice and quiet.
Guaranteed forever. Installer told me that he had been installing
them for 13 years... never replaced a single belt.

I'm (I think) going to use 1/2" thin wall conduit hung from the
ceiling with conduit hangers, and a hanger to hold the LED mechanism.

I have two doors, one a two-car and one a single car width. The
garages are amply wide... open the car doors fully. Just the peekup
truck and Q45 length are such that proper parking avoids banging knees
on bumpers ;-)

...Jim Thompson
--
| James E.Thompson, P.E. | mens |
| Analog Innovations, Inc. | et |
| Analog/Mixed-Signal ASIC's and Discrete Systems | manus |
| Phoenix, Arizona Voice:(480)460-2350 | |
| E-mail Address at Website Fax:(480)460-2142 | Brass Rat |
| http://www.analog-innovations.com | 1962 |

I love to cook with wine. Sometimes I even put it in the food.
Back to top
Joerg
Guest
Posted: Fri Feb 11, 2005 1:23 am    Post subject: Re: Slide Mount with Set Screw Reply with quote
Hello Jim,

Quote:
Illuminating the dash puts the LED about 2' toward the wall past the
opener location. The mount of the old Genie Screw Drive (Junkus
Maximus :) had angle iron sticking out that far.



High-tech. I have seen people using a simple rope and tennis ball that
touches the windshield when the car is just parked right. It's power
outage proof ;-)

Genies aren't that bad. Ours are at least 15 years old. When a relay
hung in one of them I was quite impressed about what's inside. Two
modular PCBs, with edge connectors and all. So I could take it out in a
jiffy and fix the relay inside the house instead of on a ladder in the
cold garage.

BTW, if you have an old scrap piece of copper pipe these can be used to
position pointing devices by bending until it worketh.

Regards, Joerg

http://www.analogconsultants.com
Back to top
Paul Burke
Guest
Posted: Fri Feb 11, 2005 2:49 pm    Post subject: Re: Slide Mount with Set Screw Reply with quote
Joerg wrote:

Quote:
Illuminating the dash puts the LED about 2' toward the wall past the
opener location.

High-tech. I have seen people using a simple rope and tennis ball that
touches the windshield when the car is just parked right. It's power
outage proof ;-)

Our village, having been laid out 400 years ago, lacks off- street
parking. My car is in exactly the right place (to leave enough room for
the neighbour's) when the C of "to the Church" is obscured by the
nearside roof pillar.

Paul Burke
Back to top
 
Post new topic   Reply to topic    Electronics Forum Index -> Electronics General All times are GMT
Page 1 of 1

 
 You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum



Home & Living New Topics
Contact Us
Powered by phpBB