| Author |
Message |
JamesgangNC
Guest
|
 Posted:
Tue Jan 11, 2005 8:14 am Post subject:
microwave high voltage ?s |
|
|
Working on a ge microwave. It does every but heat. The high voltage diode
tests open in both directions with my meter. I've never tested one of these
puppies before. Can I assume it tests just like an ordinary diode?
From the sound I'd say the hi voltage transformer is working. Windings
check out ok with meter as well as the filament in the tube seems ok.
Getting about 85 ohms from the filament connections to the metal case of the
tube. That's another one I'm clueless about, don't know if that's good or
bad?
Thanks in advance for any advice. I've got some regular electronics
experience but never fooled around with a microwave before.
|
|
| Back to top |
|
 |
Jerry G.
Guest
|
| Posted:
Tue Jan 11, 2005 8:22 am Post subject:
Re: microwave high voltage ?s |
|
|
You cannot test the HV diode with your meter. Your DVM would never have
enough break-over voltage to get the junction to properly conduct.
It is best to use a proper HV diode tester to check this type of diode. The
safest testing if you do not have the proper test gear, such as the HV
probe, microwave radiation checker, and etc, is to use parts substitution.
It is possible that any one or combination of parts can cause the microwave
to not function properly.
--
Jerry G.
=====
"JamesgangNC" <jamesgangnc@nospam.com> wrote in message
news:0EGEd.3855$C52.3079@newsread2.news.atl.earthlink.net...
Working on a ge microwave. It does every but heat. The high voltage diode
tests open in both directions with my meter. I've never tested one of these
puppies before. Can I assume it tests just like an ordinary diode?
From the sound I'd say the hi voltage transformer is working. Windings
check out ok with meter as well as the filament in the tube seems ok.
Getting about 85 ohms from the filament connections to the metal case of the
tube. That's another one I'm clueless about, don't know if that's good or
bad?
Thanks in advance for any advice. I've got some regular electronics
experience but never fooled around with a microwave before. |
|
| Back to top |
|
|
Sam Goldwasser
Guest
|
| Posted:
Tue Jan 11, 2005 8:27 am Post subject:
Re: microwave high voltage ?s |
|
|
"JamesgangNC" <jamesgangnc@nospam.com> writes:
| Quote: | Working on a ge microwave. It does every but heat. The high voltage diode
tests open in both directions with my meter. I've never tested one of these
puppies before. Can I assume it tests just like an ordinary diode?
From the sound I'd say the hi voltage transformer is working. Windings
check out ok with meter as well as the filament in the tube seems ok.
|
Diode has a voltage drop of 6 volts or more in the forward direction. Can't
test with meter. Need power supply and resistor.
| Quote: | Getting about 85 ohms from the filament connections to the metal case of the
tube. That's another one I'm clueless about, don't know if that's good or
bad?
|
Something shorted, probably the magnetron. Filament to case should be
open.
| Quote: | Thanks in advance for any advice. I've got some regular electronics
experience but never fooled around with a microwave before.
|
See the Microwave Oven Repair Guide at the site below, expecially the
SAFETY info.
WARNING: Microwave ovens are by far the most dangerous consumer electronic
equipment to repair and it's not mainly the microwaves but the very lethal
voltages inside.
--- sam | Sci.Electronics.Repair FAQ Mirror: http://repairfaq.ece.drexel.edu/
Repair | Main Table of Contents: http://repairfaq.ece.drexel.edu/REPAIR/
+Lasers | Sam's Laser FAQ: http://repairfaq.ece.drexel.edu/sam/lasersam.htm
| Mirror Sites: http://repairfaq.ece.drexel.edu/REPAIR/F_mirror.html
Note: These links are hopefully temporary until we can sort out the excessive
traffic on Repairfaq.org.
Important: Anything sent to the email address in the message header above is
ignored unless my full name is included in the subject line. Or, you can
contact me via the Feedback Form in the FAQs.
|
|
| Back to top |
|
|
JamesgangNC
Guest
|
| Posted:
Tue Jan 11, 2005 9:21 am Post subject:
Re: microwave high voltage ?s |
|
|
Thanks for the info everyone. If the tube's shorted then the diode might be
gone too. Guess I could test it with 110v and a light bulb. The
transformer makes enough noise to sound like it's under a load. Looks like
magnetrons are $60 or so. Probably not worth it for this 12 year old
microwave. Really nice faq on microwave repair. I was wary of the hiv
section to begin with having dealt with them on tv's and I figured to be
1000 watt microwave means that there has to be a fair amount of current to
go along with that voltage.
"Sam Goldwasser" <sam@saul.cis.upenn.edu> wrote in message
news:6wd5wc4s5b.fsf@saul.cis.upenn.edu...
| Quote: | "JamesgangNC" <jamesgangnc@nospam.com> writes:
Working on a ge microwave. It does every but heat. The high voltage
diode
tests open in both directions with my meter. I've never tested one of
these
puppies before. Can I assume it tests just like an ordinary diode?
From the sound I'd say the hi voltage transformer is working. Windings
check out ok with meter as well as the filament in the tube seems ok.
Diode has a voltage drop of 6 volts or more in the forward direction.
Can't
test with meter. Need power supply and resistor.
Getting about 85 ohms from the filament connections to the metal case of
the
tube. That's another one I'm clueless about, don't know if that's good
or
bad?
Something shorted, probably the magnetron. Filament to case should be
open.
Thanks in advance for any advice. I've got some regular electronics
experience but never fooled around with a microwave before.
See the Microwave Oven Repair Guide at the site below, expecially the
SAFETY info.
WARNING: Microwave ovens are by far the most dangerous consumer electronic
equipment to repair and it's not mainly the microwaves but the very lethal
voltages inside.
--- sam | Sci.Electronics.Repair FAQ Mirror:
http://repairfaq.ece.drexel.edu/
Repair | Main Table of Contents: http://repairfaq.ece.drexel.edu/REPAIR/
+Lasers | Sam's Laser FAQ:
http://repairfaq.ece.drexel.edu/sam/lasersam.htm
| Mirror Sites:
http://repairfaq.ece.drexel.edu/REPAIR/F_mirror.html
Note: These links are hopefully temporary until we can sort out the
excessive
traffic on Repairfaq.org.
Important: Anything sent to the email address in the message header above
is
ignored unless my full name is included in the subject line. Or, you can
contact me via the Feedback Form in the FAQs. |
|
|
| Back to top |
|
|
TeleTronic
Guest
|
| Posted:
Thu Jan 13, 2005 4:51 am Post subject:
Re: microwave high voltage ?s |
|
|
On Tue, 11 Jan 2005 02:14:20 GMT, "JamesgangNC" <jamesgangnc@nospam.com> wrote:
| Quote: | Working on a ge microwave. It does every but heat. The high voltage diode
tests open in both directions with my meter. I've never tested one of these
puppies before. Can I assume it tests just like an ordinary diode?
From the sound I'd say the hi voltage transformer is working. Windings
check out ok with meter as well as the filament in the tube seems ok.
Getting about 85 ohms from the filament connections to the metal case of the
tube. That's another one I'm clueless about, don't know if that's good or
bad?
Thanks in advance for any advice. I've got some regular electronics
experience but never fooled around with a microwave before.
If you have an analogue meter with a battery of over 6 volts,discharge the |
cap,disconnect one wire from diode,set ohms to highest range
connect leads across diode.Reading in one direction{over 50k]inf.in the other.
Filement to mag case should read inf.
A defective diode can cause the capacitor to become hot.
Also test the cap on a high Ohms range[Analogue meter] you should get a needle
kick and slow decay.You can't test with digi.meter. |
|
| Back to top |
|
|
|
|
|
|
FAQ
Memberlist
Register
Profile
Log in to check your private messages
Log in