| Author |
Message |
pil
Guest
|
 Posted:
Wed Dec 22, 2004 11:21 pm Post subject:
heater circuit |
|
|
I need to control a simple heating element which will run off 12Vdc. It does
not need to get very hot.
I need to make it variable. At the moment I have a 555 running in astable
mode pulsing two MJ13005 transistors which are directly connected to the
element. The transistors seem to get too hot. What other methods can I use?
My element usualy are a bunch of fine stranded copper wires and the one I am
currently using has a resistance of 5ohms.
I need to run this off 12Vdc.
|
|
| Back to top |
|
 |
John Popelish
Guest
|
| Posted:
Wed Dec 22, 2004 11:57 pm Post subject:
Re: heater circuit |
|
|
pil wrote:
| Quote: |
I need to control a simple heating element which will run off 12Vdc. It does
not need to get very hot.
I need to make it variable. At the moment I have a 555 running in astable
mode pulsing two MJ13005 transistors which are directly connected to the
element. The transistors seem to get too hot. What other methods can I use?
My element usualy are a bunch of fine stranded copper wires and the one I am
currently using has a resistance of 5ohms.
I need to run this off 12Vdc.
|
I think the power transistors you are using are high voltage, low gain
types. So they need a lot of base current to get fair saturation. If
you replace them with a low resistance N-channel mosfet, that should
run much cooler. They are also much simpler to connect to the 555.
The gate can be connected directly to the 555 output.
Go to Digikey and find the data sheets for IRFZ44V, IRF540, IRF3704
for examples that should work. One of these can handle your load with
no heat sink.
--
John Popelish |
|
| Back to top |
|
|
Anthony Fremont
Guest
|
| Posted:
Thu Dec 23, 2004 12:04 am Post subject:
Re: heater circuit |
|
|
"pil" wrote:
| Quote: | I need to control a simple heating element which will run off 12Vdc.
It does
not need to get very hot.
I need to make it variable. At the moment I have a 555 running in
astable
mode pulsing two MJ13005 transistors which are directly connected to
the
element. The transistors seem to get too hot. What other methods can I
use? |
Are you using the transistors in parallel? What frequency is your 555
running at? Duty Cycle? Schematic?
All that aside, worst case gain for that transistor is only 8 (Ic=2A)
which means you will need to supply at least 300mA (each) of drive into
the base to turn the transistors on all the way. AFAIK, the 555 can't
supply that much current by itself. What you need is a nice MOSFET,
preferably one that uses a "logic level" input.
| Quote: | My element usualy are a bunch of fine stranded copper wires and the
one I am
currently using has a resistance of 5ohms. |
|
|
| Back to top |
|
|
Guest
|
| Posted:
Mon Dec 27, 2004 9:00 am Post subject:
Re: heater circuit |
|
|
Couldn't find much on your transistors.
2 things, Use a better transistor like a MOSFET that has a low switched
on resistance.
2nd, use the pulse width function of the 555 to adjust the temp. you
will only need one transistor instead of 2 drives.
A predrive may be needed. You are running about 2.5 amps
There are many devices out there that would work I would get one about
5 amps and a med. heat sink.
Mr. Eric Spain |
|
| Back to top |
|
|
|
|
|
|
FAQ
Memberlist
Register
Profile
Log in to check your private messages
Log in