Sony DvD repair
Electronics Forum Index Electronics
Circuits, theory, electrons and discussions.
 
 FAQFAQ   MemberlistMemberlist     RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 
 
Google
 
Web ElectronicsHelp.net
Sony DvD repair
Goto page 1, 2  Next
 
Post new topic   Reply to topic    Electronics Forum Index -> Repair
Author Message
huneebee23
Guest
Posted: Thu Apr 28, 2005 6:02 am    Post subject: Sony DvD repair Reply with quote
My DvD player (model DvP-NS300) will not read the disc. It seems the
thing that turns the disc isn't gripping. Maybe I am wrong, but I
hope someone has a remedy.

Back to top
riki
Guest
Posted: Thu Apr 28, 2005 8:17 am    Post subject: Re: Sony DvD repair Reply with quote
The black crowes might no the answer
Back to top
spudnuty
Guest
Posted: Thu Apr 28, 2005 4:35 pm    Post subject: Re: Sony DvD repair Reply with quote
Hmm now that I read your post more carefully have you checked that the
spindle is firmly attached to the drive motor?
Richard

Back to top
spudnuty
Guest
Posted: Thu Apr 28, 2005 4:35 pm    Post subject: Re: Sony DvD repair Reply with quote
Don't know this particular player but I recently fixed a Sony DVP-NC600
with this same problem. When I opened it up I found that the board that
was directly connected to the transport mechanicals had two bad "fish
caps" on it. (used Dave's ESR meter! search this forum for more info on
fish caps) I replaced them, got the parts from Mouser, and the player
has been working great for 7 months now.
Richard
Back to top
JANA
Guest
Posted: Thu Apr 28, 2005 4:35 pm    Post subject: Re: Sony DvD repair Reply with quote
Your question is very vague for a proper answer.

You would have to post the readings of things like if the power supply has
been properly checked, such as the voltage outputs, and also a description
of the checks that have been done to the transport, and especially the laser
assembly. \

If you feel it is worth the cost, take the unit in to a shop that services
CD players. Let them do an estimate for you. You can then make an
intelligent decision if the unit is worth to service or not.

--

JANA
_____


"huneebee23" <huneebee23@yahoo-dot-com.no-spam.invalid> wrote in message
news:de40c$42703619$455da0d2$1574@allthenewsgroups.com...
My DvD player (model DvP-NS300) will not read the disc. It seems the
thing that turns the disc isn't gripping. Maybe I am wrong, but I
hope someone has a remedy.
Back to top
Sound Man
Guest
Posted: Wed May 18, 2005 8:35 am    Post subject: Re: Sony DvD repair Reply with quote
Hi folks,

I'm having similar problems with my Sony DVD DVP-NC600. Sometimes when
I give the disc a spin the motor will engage and it will read the
disc.

So the motor does work. Maybe it just not catching the disk.

Any ideas?

Thanks!
Back to top
Mark D. Zacharias
Guest
Posted: Wed May 18, 2005 3:19 pm    Post subject: Re: Sony DvD repair Reply with quote
Sound Man wrote:
Quote:
Hi folks,

I'm having similar problems with my Sony DVD DVP-NC600. Sometimes when
I give the disc a spin the motor will engage and it will read the
disc.

So the motor does work. Maybe it just not catching the disk.

Any ideas?

Thanks!

Actually, it is the motor. You've just nudged it past the bad spot where the
brushes contact the commutator. The motor is not sold separately, but part
of the pickup assembly. Mine did the same thing. Also, I'm an authorized
Sony servcer, so I have a bit of experiemce with these.

Mark Z.
Back to top
sofie
Guest
Posted: Thu May 19, 2005 12:35 am    Post subject: Re: Sony DvD repair Reply with quote
Exactly correct.
Back to top
Sound Man
Guest
Posted: Thu May 19, 2005 12:35 am    Post subject: Re: Sony DvD repair Reply with quote
Ahh. And how do I get the pickup assembly? Do you think I can order it
online somewhere or do I need a service dealer to order it?
Back to top
Sound Man
Guest
Posted: Thu May 19, 2005 6:44 am    Post subject: Re: Sony DvD repair Reply with quote
I found it at www.electronix.com part number KHM240AAA. $26 +
shipping. It beats buying a new one.

Thanks for you help! :D
Back to top
Mark D. Zacharias
Guest
Posted: Thu May 19, 2005 2:11 pm    Post subject: Re: Sony DvD repair Reply with quote
Sound Man wrote:
Quote:
I found it at www.electronix.com part number KHM240AAA. $26 +
shipping. It beats buying a new one.

Thanks for you help! :D

There will be a "solder short" on the new one which must be cleared before
the new one will function.
Additionally, there is a simple setup procedure for the Sony which is run
using the onscreen menus, etc. Post back when you get it running and we'll
walk you through it.
There has been an issue with used, defective pickups being sold by some
vendors. Beware.

Mark Z.
Back to top
Ewan D. Milne
Guest
Posted: Mon May 30, 2005 6:14 pm    Post subject: Re: Sony DvD repair Reply with quote
Mark D. Zacharias wrote:
Quote:
Sound Man wrote:
I found it at www.electronix.com part number KHM240AAA. $26 +
shipping. It beats buying a new one.

Thanks for you help! :D

There will be a "solder short" on the new one which must be cleared before
the new one will function.
Additionally, there is a simple setup procedure for the Sony which is run
using the onscreen menus, etc. Post back when you get it running and we'll
walk you through it.
There has been an issue with used, defective pickups being sold by some
vendors. Beware.

Mark Z.

I recently purchased one of these from www.electronix.com and after I
installed it, the DVD player would not come out of standby mode -- the
power LED would change from green to red for a second, then go back to
red.
There was never any video output. I put the old pickup back in and
that
problem went away. Can you describe where the "solder short" is that
has to be cleared?

Interestingly enough, the DVD player worked for a couple of days after
I put the old pickup back in, and then it stopped working again. It
seems
like the problem that causes the NO DISC error is that the disk doesn't
start spinning.

-Ewan
Back to top
Mark D. Zacharias
Guest
Posted: Tue May 31, 2005 12:12 am    Post subject: Re: Sony DvD repair Reply with quote
Ewan D. Milne wrote:
Quote:
Mark D. Zacharias wrote:
Sound Man wrote:
I found it at www.electronix.com part number KHM240AAA. $26 +
shipping. It beats buying a new one.

Thanks for you help! :D

There will be a "solder short" on the new one which must be cleared
before the new one will function.
Additionally, there is a simple setup procedure for the Sony which
is run using the onscreen menus, etc. Post back when you get it
running and we'll walk you through it.
There has been an issue with used, defective pickups being sold by
some vendors. Beware.

Mark Z.

I recently purchased one of these from www.electronix.com and after I
installed it, the DVD player would not come out of standby mode -- the
power LED would change from green to red for a second, then go back to
red.
There was never any video output. I put the old pickup back in and
that
problem went away. Can you describe where the "solder short" is that
has to be cleared?

Interestingly enough, the DVD player worked for a couple of days after
I put the old pickup back in, and then it stopped working again. It
seems
like the problem that causes the NO DISC error is that the disk
doesn't start spinning.

-Ewan

The solder bridge on this pickup, I believe, is visible on the right side of
the complete pickup subchassis as viewed from the front of the unit while
the pickup subchassis is installed. That way all the plugs etc are installed
before the solder is cleared.

On the other pickup from Electronix, sounds like mabye the slider motor was
jammed up.

It's not too uncommon for dvd pickups to be intermittent like your old one
was.

Mark Z.
Back to top
Ewan D. Milne
Guest
Posted: Tue May 31, 2005 12:36 am    Post subject: Re: Sony DvD repair Reply with quote
Thanks very much for replying -- I can see what appears to be two pairs
of
semicircular pads facing each other -- one pair on top of the board and
one
pair on the bottom of the board (right on top of each other, as it
were).
It doesn't look like there is a solder bridge on either of them,
though.
The pads are right next to the wider of the two ribbon cable
connectors.

I found that the DVD player (a DVP-NS300) would power up if the
narrower
ribbon cable was disconnected. It wouldn't work, but it would get out
of
standby.

-Ewan
Back to top
Mark D. Zacharias
Guest
Posted: Tue May 31, 2005 2:47 pm    Post subject: Re: Sony DvD repair Reply with quote
Ewan D. Milne wrote:
Quote:
Thanks very much for replying -- I can see what appears to be two
pairs of
semicircular pads facing each other -- one pair on top of the board
and one
pair on the bottom of the board (right on top of each other, as it
were).
It doesn't look like there is a solder bridge on either of them,
though.
The pads are right next to the wider of the two ribbon cable
connectors.

I found that the DVD player (a DVP-NS300) would power up if the
narrower
ribbon cable was disconnected. It wouldn't work, but it would get out
of
standby.

-Ewan

I did think we were talking about a DVP-NC600, but the pickup is the same as
I recall. The solder blob would be near where one of the cables plugs in at
the side. The solder pads on the pickup itself are not used. Been fooled by
this one before.

mz
Back to top
 
Post new topic   Reply to topic    Electronics Forum Index -> Repair All times are GMT
Goto page 1, 2  Next
Page 1 of 2

 
 You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum



Home & Living New Topics
Powered by phpBB