| Author |
Message |
Rich Grise
Guest
|
 Posted:
Sun Mar 06, 2005 6:10 am Post subject:
Re: Stacking PCB's |
|
|
On Sat, 05 Mar 2005 19:15:09 -0600, James T. White wrote:
| Quote: | "Harold Ryan" <hryan@chartermi.net> wrote in message
news:BdlWd.6368$oV7.5266@fe07.lga...
For thruhole boards, this would not be possible. Can't solder the connector
to the board. However, for surface mount, just use any male/female connector
pair. This will have an alignment issue.
Harold
Then PC-104 products must not exist since they use exactly this type of
connector.
|
Even ordinary wire-wrap IC sockets will work - I did that once with a
daughterboard. Don't use the machined-pin kind - use sockets that will
take a .025" pin.
Cheers!
Rich
|
|
| Back to top |
|
 |
Harold Ryan
Guest
|
| Posted:
Sun Mar 06, 2005 6:10 am Post subject:
Re: Stacking PCB's |
|
|
I believe a tool is required to press the connector into the board. Is that
correct?. The solder type of connector is not stackable.
Harold
"James T. White" <SPAMjtwhiteGUARD@SPAMhal-pcGUARD.org> wrote in message
news:422a5888$0$64585$a726171b@news.hal-pc.org...
| Quote: | "Harold Ryan" <hryan@chartermi.net> wrote in message
news:BdlWd.6368$oV7.5266@fe07.lga...
For thruhole boards, this would not be possible. Can't solder the
connector
to the board. However, for surface mount, just use any male/female
connector
pair. This will have an alignment issue.
Harold
Then PC-104 products must not exist since they use exactly this type of
connector.
--
James T. White
|
|
|
| Back to top |
|
|
James T. White
Guest
|
| Posted:
Sun Mar 06, 2005 6:10 am Post subject:
Re: Stacking PCB's |
|
|
"Harold Ryan" <hryan@chartermi.net> wrote in message
news:BdlWd.6368$oV7.5266@fe07.lga...
| Quote: | For thruhole boards, this would not be possible. Can't solder the connector
to the board. However, for surface mount, just use any male/female connector
pair. This will have an alignment issue.
Harold
|
Then PC-104 products must not exist since they use exactly this type of
connector.
--
James T. White
|
|
| Back to top |
|
|
Fred Abse
Guest
|
| Posted:
Sun Mar 06, 2005 10:04 pm Post subject:
Re: Stacking PCB's |
|
|
On Sat, 05 Mar 2005 19:12:14 +0000, Clarence_A wrote:
| Quote: |
"Harold Ryan" <hryan@chartermi.net> wrote in message
news:BdlWd.6368$oV7.5266@fe07.lga...
Top Poster --- PLONK!
|
Plonker - <PLONK>
--
Then there's duct tape ...
(Garrison Keillor) |
|
| Back to top |
|
|
Harold Ryan
Guest
|
| Posted:
Wed Mar 09, 2005 6:10 am Post subject:
Re: Stacking PCB's |
|
|
Thanks James
Harold
"James T. White" <SPAMjtwhiteGUARD@SPAMhal-pcGUARD.org> wrote in message
news:422a8ab5$0$64589$a726171b@news.hal-pc.org...
| Quote: | "Harold Ryan" <hryan@chartermi.net> wrote in message
news:YnvWd.214$Ho6.132@fe03.lga...
I believe a tool is required to press the connector into the board. Is
that
correct?. The solder type of connector is not stackable.
Harold
Sorry to burst your bubble Harold, but I just installed several sets of
stacking
connectors by soldering them onto a boards Friday.
Here is the Samtec catalog pages for the connectors we use -
http://www.samtec.com/ftppub/pdf/ESQ_TH.PDF
http://www.samtec.com/ftppub/pdf/SSQ_TH.PDF
To solder them with an iron, you push the long square tails through the
board
holes from the top side of the board until the socket bottoms against the
board
and solder the pins down next to the board on the backside. If you are
using
the three row SSQs, hand soldering the center row of pins is difficult but
it
can be done. For reflow soldering, you put solder preforms on the
connector
pins (or buy connectors with preforms already installed), push the
connector all
the way down on the board and reflow using hot air.
--
James T. White
|
|
|
| Back to top |
|
|
|
|
|
|
FAQ
Memberlist
Register
Profile
Log in to check your private messages
Log in