| Author |
Message |
Guest
|
 Posted:
Tue Sep 13, 2005 5:56 am Post subject:
PCB hardware? |
|
|
I'm designing a system that uses two PCBs that connect together with
Samtec QSE-DP connectors. I need some sort of mechanical latch system
that will allow quick connect/disconnect and provide some mechanical
stability.
Does that exist? Short of using a 10-32 screw with a butterfly nut, I'm
coming up empty. Google searches reveal nothing.
I am not looking for quick disconnect connectors, just some sort of
latch or PCB mountable PEM nut.
|
|
| Back to top |
|
 |
Ken
Guest
|
| Posted:
Tue Sep 13, 2005 4:37 pm Post subject:
Re: PCB hardware? |
|
|
a7yvm109gf5d1@netzero.com wrote:
| Quote: | I'm designing a system that uses two PCBs that connect together with
Samtec QSE-DP connectors. I need some sort of mechanical latch system
that will allow quick connect/disconnect and provide some mechanical
stability.
Does that exist? Short of using a 10-32 screw with a butterfly nut, I'm
coming up empty. Google searches reveal nothing.
I am not looking for quick disconnect connectors, just some sort of
latch or PCB mountable PEM nut.
|
I don't know about the mechanical stability you need, but depending
upon how often you need to separate the PWBs, I have seen Panduit Ties
used as a means of holding a connector together. Sometimes there are
holes in the PWB or the size of the PWB allows the tying over the outer
edges. There are also many Nylon standoffs that have a locking tab that
latches on to both PWBs through holes in the boards. |
|
| Back to top |
|
|
Guest
|
| Posted:
Wed Sep 14, 2005 6:46 am Post subject:
Re: PCB hardware? |
|
|
Thanks for the reply. I should be a bit more specific: the second board
is three times as large as the first board. Its purpose is to break out
a bunch of signals to SMA connectors. So it doesn't need more than a
few pounds of retaining strength.
It should be a single point of attachment with a simple hand-oprated
mechanism. I don't want people to have to look for a tool.
My backup plan is nylon screws with some sort of surface mountable
bolts. I will lose PCB space and it will be unwieldy.
"There are also many Nylon standoffs that have a locking tab"
I think you mean those nylon mounts for motherboards, right? You still
need a tool to squish the nylon, but if I can find who makes those,
maybe they make a big one and I can squeeze it by hand.
Back to the Google...
|
|
| Back to top |
|
|
Robert Baer
Guest
|
| Posted:
Wed Sep 14, 2005 8:35 am Post subject:
Re: PCB hardware? |
|
|
a7yvm109gf5d1@netzero.com wrote:
| Quote: | Thanks for the reply. I should be a bit more specific: the second board
is three times as large as the first board. Its purpose is to break out
a bunch of signals to SMA connectors. So it doesn't need more than a
few pounds of retaining strength.
It should be a single point of attachment with a simple hand-oprated
mechanism. I don't want people to have to look for a tool.
My backup plan is nylon screws with some sort of surface mountable
bolts. I will lose PCB space and it will be unwieldy.
"There are also many Nylon standoffs that have a locking tab"
I think you mean those nylon mounts for motherboards, right? You still
need a tool to squish the nylon, but if I can find who makes those,
maybe they make a big one and I can squeeze it by hand.
Back to the Google...
There are nylon screws that work with a screwdriver, and also can be |
pushed in by hand; sounds almost opposite of what you describe, but...
....maybe they can also be pushed out.
Then there are nylon panel fasteners that can snap in and be pushed
out if the hole is reasonably matched to the fastener.
For example, see Mouser 561-SCR252050 (1/4-20 "spin-clips" 0.5 long)
and similar parts, as well as Mouser 561-RT1870 (rachet fastener, 0.187
hole size, panel thickness 0.025-0.365) and similar.
They also have "key-hole clips" 561-Y1250125 (and similar) as well
as a variety of rivet variants. |
|
| Back to top |
|
|
|
|
|
|
FAQ
Memberlist
Register
Profile
Log in to check your private messages
Log in